How do I reset my DStv after load shedding?

Decoder Showing Red Light And No Signal Being Sent To TV After Load Shedding

1. You need to switch off your DSTV Decoder from the plug.
2. Remove the decoder power cable from the power source.
3. Unscrew the white cable at the back of the decoder coming from the LNB.
4. Leave cables unplugged for a period of 3 minutes.

How do I get my DStv signal back?

How To Fix Signal Strength On DStv?

1. Check F-type connectors. Check for incorrectly connected F-type connectors on the LNB and at the back of the decoder.
2. Correct the LNB alignment.
3. Adjust satellite dish alignment.
4. Replace a faulty LNB.
5. Move your satellite dish.
6. Cut down or prune trees that may obstruct the signal.

What do you do when your DStv decoder stops working?

How To Fix Dstv Decoder Not Powering Up

1. Turn off the decoder and switch off the power source.
2. Remove the power cord from the decoder.
3. Unplug all peripherals plugged in.
4. After 10minutes, reconnect the power cable and see if the DStv decoder is powering up.

How do I reset my DStv decoder?

Press the blue “DStv button” on your remote control. Then use the right arrow on the remote control to go to “Settings“. Use the down arrow to go to “System Settings“. Scroll down using the down arrow to select “Reset To Factory Default” then press “OK” on your remote control.

How do I get my DStv decoder out of standby mode?

To reset your decoder manually; Press the reset and standby button at the same time. Immediately you see the letters, press standby P+P_ this must be done on a quick succession one after the other for effect.

Why is my DStv decoder blinking orange light?

If your subscription is running out, you need to update, or there is an upcoming show saved, you will receive the orange light on DStv decoder. It is very convenient and will ensure you never miss out on any important information from Multichoice.

Why is my decoder showing no signal?

The reason your DStv says no signal is because there is an error in the DStv installation. This is caused by either a misaligned satellite dish, a faulty LNB, an improperly connected F-connector plug, loose cables or incorrect decoder settings on the LNB type.

Can a DStv decoder be repaired?

The standard repair fee is R700 for an HDPVR / Explora and R320 for a Single View decoder. If you have decoder insurance, you will not be required to pay the repair fee as this is included in your cover. When you bring your decoder in, you will be given a refurbished model as a replacement.

Can a decoder be fixed?

DStv decoders which can be fixed or replaced MultiChoice is able to repair and refurbish the majority of older decoders, it said. Customers are usually given a refurbished model while their decoder is repaired. MultiChoice charges a repair fee of: R698 for a PVR model.

How do I reset my DStv decoder without the remote?

Process of how to reset DStv decoder without remote First, unplug the power button from your decoder and ensure it is completely turned off. You can check for this by ensuring all its lights are turned off, and none is blinking. Turn it back on and press the reset button on your decoder.

What does red light mean on DStv decoder?

A common error when the red light comes up is the smart card setup. If you insert your smart card incorrectly, it will bring this indication. All you need to do is remove, dust, and re-insert your smart card. This should fix the problem and if it persists, just reboot the decoder.

How to fix DStv decoder not working?

Step 1: Disconnect and Reconnect the dish cable from the DSTV decoder: This is very important, so carefully trace out the dish cable and disconnect it, then reconnect the dish signal cable back to the decoder. Step 2: Now restart the decoder, either by using the power button or unplugging it from the wall socket, then plug it back.

How to solve DStv installation wizard error and channels scanning problems?

Solve DStv decoder installation wizard error and channels scanning problems by factory resetting your decoder using the P+ and P- buttons. After releasing the P+ button, press -++- in quick succession and your decoder will be able to scan once again. It will also be ready to complete the installation wizard successfully.

How to fix Dish Network DStv not working?

Also note that it require little or no technical knowledge. Step 1: Disconnect and Reconnect the dish cable from the DSTV decoder: This is very important, so carefully trace out the dish cable and disconnect it, then reconnect the dish signal cable back to the decoder.

How do I Fix my Multichoice TV decoder?

To fix this we need to reboot the decoder this way Wait for decoder to scan. If the steps above did not fix the problem, then I would advise you to take your decoder to Multichoice to be tested, if your decoder is insured then you will get it replaced free of charge by Multichoice.