Can you use caulk between floorboards?

Acrylic latex caulk will allow for the greatest flexibility between the floorboards and is also one of the easiest caulks to work with and clean up.

How do you fill nail holes in hardwood floors?

Starts here0:32How to Fill Nail Holes in Finished Wood – YouTubeYouTubeStart of suggested clipEnd of suggested clip29 second suggested clipWhen you’re feeling nail holes an unfinished wood like this use a color matched wood putty like oneMoreWhen you’re feeling nail holes an unfinished wood like this use a color matched wood putty like one of these. Apply. It with a putty knife let it dry. And then sand it smooth.

Can polyurethane be applied over old polyurethane?

As long as you use the proper steps to prepare the finish, you can put polyurethane over old polyurethane. But before you apply the topcoat polyurethane, you might have to first sand the surface lightly using a dull 120 to 150 grit abrasive screen using a heavy floor buffer.

How do you get scratches out of polyurethane on hardwood floors?

To remove scratches from polyurethane coating, moisten a scouring pad with mineral spirits. Gently rub the scratch with the pad. Allow it to dry and wipe off. Use a colored wood putty that matches your floor.

How do you seal gaps between floorboards?

How to Fill Floorboard Gaps With Wood Strips

1. Cut the Strips. Measure the width and length of each gap between floorboards.
2. Glue the Strips in Place. Apply wood glue to the sides of each strip and gently tap it into the gap, using a mallet or hammer.
3. Sand and Stain the Strips.

How do you fill gaps in old wooden floorboards?

Starts here3:59How to Fix Wood Floor Gaps Easily? – YouTubeYouTube

What do you use to fill gaps between floorboards?

Filling large gaps with natural-fiber rope is a traditional method commonly used on wide plank floorboards in very old homes. While the rope doesn’t look like wood, you can stain it to blend with the floorboards, and the filled gaps will be much less noticeable than the dark, empty gaps.

What is the best caulking for wood floors?

As a siliconized acrylic adhesive caulk, ColorRite works well and cleans up easily. Additionally, it fills up to a ¼” gap and resists mold, mildew, and moisture. It also is easy to apply, just follow the direction on the package.

What is the best wood filler for nail holes?

For the best wood filler for nail holes, consider Elmer’s E855 Carpenter’s Wood Filler. The product comes in a nice 3.25-oz tube that is so easy to operate.

Can you refinish hardwood floors with nails?

As long as there is a subfloor to support it, there really isn’t a limit to the number of sandings you can do on a face-nailed plank floor. A word of caution here: If the nails are flush or are protruding above the surface of the planks, then you should drive them below the surface with a nail set before sanding.

How do you repair a crack in a floorboard?

To repair a crack in an otherwise sound board, glue down any long splinters, then fill the crack with wood filler or wood putty. Both plank and tongue-and-groove floors can develop unsightly gaps as the floor ages. This is caused by compression shrinkage. During periods of high humidity, a floorboard will expand and compress its neighbors.

Should I fill gaps between wood floor boards?

Filling gaps between wood floor boards invites later buckling or causes further compression of the edges of boards when they next expand. You can see that’s what’s been happening with the putty-filled wood floor gaps in my parquet wood floor gap photo at left.

How do you repair hardwood floors with Brads?

Glue or toenail the strips with brads to each board, or face-nail them to the joists or subfloor. The repair may need to be hand-planed or sanded to match the level of the floor. Chlorine, oxalic acid, and hydrogen peroxide are the most effective stain removers for wood floors.

What kind of nails do you use to pull down hardwood floors?

If the board is loose but not hard to pull down, using 6d stainless ring-shank nails driven through a pre-drilled (smaller bit than nail) hole may work best and will allow you to counter-sink the nail head at least 1/8″ below the floor surface. For floor boards that are hard to pull down by nailing screws may be more effective.